제품소개
1066의 게이트 셀렉션은 주파수에 의존적인 게인 컨트롤과 측면 체인 모니터 버튼(SC MON)을 사용하여 원하지 않는 주파수나 마이크 출혈을 깨끗하게 하게 해준다.
사이드 체인 모니터 버튼(SC Mon)과 이퀄라이저를 사용하면, 게이트 (차단)를 일으키는 주파수를 선택할 수 있다.
전체적인 스피커 보호를 위해서, 우리의 혁신적인 PeakStopPlus 기술은 당신의 드라이버 폭발로부터 원하지 않는 과도전류(transient)를 막고, 많은 다른 하드 리미터에 공통적으로 왜곡을 최소화한다. 스튜디오, 방송시설, 순회공연 어디든, 1066은 직관적인 동작을 위해서 설계되었다.
원하지 않는 신호를 제거, 신호 게인을 제어하고, 전체적인 믹스를 보호해 줄 뿐만 아니라, 듀얼 모노나 스테레오 모드에서 그렇게 하도록 해준다.
선택가능한 입력과 출력 계량(metering)과 결합된 이것은 레벨을 맞추고 신호대 잡음비를 최대화하는데 도움을 준다.
그러나 거기서 멈추지 앟았다.
읽기 쉽고, 동작하기 위한 스냅을 만드는 우리의 특허 받은 LightPipe 기술을 가지고 대부분의 장치에서 발견되는 모호한 LED를 대체했다.
완전한 부품 선택, 엄격한 테스팅 그리고 가장 중요하게 여겨지는 장대한 사운드를 더한 이러한 모든 특징이 dbx 1066을 시장에서 가장 좋은 프로세서 중에 하나로 만드는데 기여했다.
특징
• Selectable auto (classic dbx®) or manual (variable Attack and Release) compression
• Contour switch removes unwanted low frequency information from detector circuit
• Selectable Overeasy® or Hard Knee compression modes
• PeakStopPlus™ limiting for setting maximum allowable level with minimal distortion
• SC Ext and SC Mon for setting up and monitoring external devices for gating function
• True differentially balanced gold-plated XLR and 1/4" inputs and outputs
• True RMS level detection
• Precision metering of input level, output level, and gain reduction
• True stereo or dual mono operation
• Switchable +4dBu or -10dBV operation per channel
스펙
INPUT
Connectors: XLR and 1/4" TRS (Pin 2 and tip hot)
Type: Electronically balanced/unbalanced, RF filtered
Impedance: Balanced > 50 kOhm, unbalanced >25 kOhm
Maximum Input Level: > +24 dBu balanced or unbalanced
CMRR: Typically >50 dB at 1 kHz
OUTPUT
Connectors: XLR and 1/4" TRS (Pin 2 and tip hot)
Type: Servo-balanced/unbalanced, RF filtered
Impedance: Balanced 120 Ohm, unbalanced 60 Ohm
Max Output Level: > +21 dBm balanced, > +20 dBm unbalanced
SIDECHAIN INPUT
Connector: 1/4" TS
Type: Unbalanced, RF filtered
Impedance: >10 kOhm
Max Input Level: >+24 dBu
SIDECHAIN OUTPUT
Connector: 1/4" TRS (tip hot)
Type: Impedance balanced, RF filtered
Impedance: Balanced 2 kOhm, unbalanced 1 kOhm
Max Input Level: >+21 dBu balanced or unbalanced
SYSTEM PERFORMANCE
Bandwidth: 20 Hz to 20 kHz, +0/0.5 dB
Frequency Response: 0.35 Hz to 90 kHz, +0/-3 dB
Noise: < -96 dBu, unweighted, 22 kHz measurement bandwidth
Dynamic Range: > 118dB, unweighted
THD + Noise: 0.008% typical at +4 dBu, 1 kHz, unity gain 0.08% typical at +20 dBu, 1 kHz, unity gain< 0.1% any amount of compression up to 40 dB, 1 kHz
IMD: < 0.1% SMPTE
Interchannel Crosstalk: < -80dB, 20 Hz to 20 kHz
Stereo Coupling: True RMS Power Summing™
COMPRESSOR
Threshold Range: -40 dBu to +20 dBu
Ratio: 1:1 to infinity:1
Threshold Characteristic: Selectable OverEasy® or hard knee
Attack/Release Chracteristic: Auto Dynamic™
Attack/Release Modes: Selectable Manual or Auto
Manual Attack Time: Scalable program-dependent
Manual Release time: Scalable program-dependent
Auto Attack Time: Program-dependent
Auto Release Time: Program-dependent
Output Gain: -20 to +20 dB
LIMITER
Threshold Range: +4 dBu to +24 dBu (off)
Ratio: infinity:1
Limiter Type: PeakStopPlus™ two-stage limiter
Stage 1: PeakStop™ brickwall limiter
Attack time: Zero
Release Time: Zero
Stage 2: Predictive intelligent program limiter
Attack Time: Program-dependent
Release Time: Program-dependent
EXPANDER/GATE
Threshold Range: Off to +15dBu
Ratio: 1:1 to 30:1
Attack Time: < 100 µsec
Release Time: Program-dependent
FUNCTION SWITCHES
SC Ext.: Routes the external sidechain input signal to the detector
SC Mon: Routes the sidechain signal to the output, interrupting the normal audio
OverEasy®: Activates the OverEasy compression function
Contour: Activates the frequency-dependent detector function
Auto: Activates automatic program-dependent attack and release times, disabling the manual Attack and Release controls
I/O Meter: Switches between monitoring input and output levels on the Input/Output Level meter
Bypass: Activates the direct input-to-output hard-wire relay bypass. Relay automatically hard-wire bypasses unit at power-down and provides a power-on delay of 1.5 sec.
Operating Level (rear panel): Switches the nominal operating level between -10 dBV and +4 dBu simultaneoulsy for both input and output levels
ST Link: Link both channels for stereo operation. Channel One becomes the master
INDICATORS
Gain Reduction Meter: 12-segment LED bar graph at 1, 2, 4, 6, 9, 12, 15, 18, 21, 24, 27 and 30 dB
Input/Output Meter: 8-segment LED bar graph at -24, -18, -12, -6, 0, +6, +12, and +18 dBu
Compressor Threshold Meter: 3-segment LED bar graph at Below (-), OverEasy and Above (+)
Exp/Gate Threshold Meter: 2-segment LED bar graph at Below (-) and Above (+)
Limiter, Threshold Meter: 1 LED to indicate PeakStopPlus™ limiting
Function Switches: LED indicator for each front-panel switch
OPTIONS - Output Transformer
Per Channel: Jensen® JT-123-dbx or JT-11-dbx, BCI RE-123-dbx or RE-11-dbx
POWER SUPPLY
Operating Voltage: 100-120 VAC 50/60 Hz 200-240 VAC 50/60 Hz
Power Consumption: 20 Watts
Fuse: 100-120 VAC: 250 mA Slow Blow
200-240 VAC: 125 mA Type T
Mains Connection: IEC receptacle
PHYSICAL
Dimensions: 1.75"Hx19"Wx9"D (4.4cmx48.3cmx20.1cm)
Weight: 5.1 lbs. (2.3 kg)
Shipping Weight: 7.5 lbs. (3.4 kg)
1066 |
Inputs
|
XLR and 1/4" TRS (Pin 2 and tip hot)
Balanced > 50 k Ohm, unbalanced >25 k Ohm
+24 dBu, Balanced or Unbalanced
|
Outputs
|
1/4" TRS phone, Unbalanced
120Ω balanced, 60Ω unbalanced
+21dBu,>+20 dBm into 600Ω,
|
Frequency Response
|
20 Hz ~ 20 kHz; +0, -0.5 dB, Typical 3 dB
|
Dynamic Range
|
> 118 dB, unweighted
|
Thd+Noise
|
0.008% typical at +4 dBu, 1 kHz, unity gain 0.08% typical at +20 dBu, 1 kHz, unity gain < 0.1% any amount of compression up to 40 dB, 1 kHz
|
Dimensions
|
4.4(H) x 48.3(W) x 20.1(D) cm |